BMW sets 9 records with Hydrogen Combustion Engine

Press Release

VALVETRONIC providing optimum conditions for hydrogen drive

Exclusive to BMW, VALVETRONIC technology serving as a standard feature to mastermind the valves on the 12 cylinder gives the Company's engine development specialists an ideal tool for controlling this demanding gas charge cycle. VALVETRONIC controls not only the duration of valve movement, but also the actual valve lift. This effect is provided by an intermediate lever between the camshaft and the two intake valves on each cylinder infinitely modified in its position relative to the camshaft by an additional eccentric shaft operated by an electric motor. Depending on the position of this eccentric shaft, the lever transforms the "hump" on the cams into a larger or smaller valve movement.

VALVETRONIC is based consistently on BMW's infinite camshaft adjustment process. Already well-known under its trade name VANOS, this system is an integral part of the VALVETRONIC concept. Incorporating a hydraulically controlled adjuster unit in the camshaft drive, VANOS modifies the beginning and end of the valve opening period, fully variable valve management serving to adjust the gas charge cycle in the 12 cylinder power unit perfectly to the requirements and characteristics of hydrogen drive.

Special injection valves for hydrogen power

With hydrogen being injected into the intake manifold as late as possible, the injection valves have to meet very demanding requirements. Hence, the valves are a trendsetting new development for BMW. And since gaseous hydrogen takes up a larger volume per unit of energy than liquid gasoline, the hydrogen injection valves are larger than conventional injection valve units.

A further point is that the valves have to cover a far wider range of different features and requirements, operating under all kinds of system pressure levels and with injection periods ranging from very short to relatively long. One of the main objectives in developing the valves was to inject exactly the right amount of hydrogen required into the intake manifold within a very short time-frame at very high engine speeds and under full load.

A clean mixture formation process: less fuel consumption under part load, extra power under full load

Under full load the 12 cylinder power unit runs on a fuel/air mixture of lambda = 1. This is exactly the same mixture we also find on a state-of-the-art gasoline engine, the mixture which, in principle, offers the highest and most efficient power output in a combustion engine. Under part load - again a significant benefit offered by hydrogen - the engine runs efficiently in the lean burn mode with surplus air.

Under specific conditions, that is with a specific fuel/air mixture, the combustion of hydrogen leads to the generation of nitric oxides. This mixture "slot" starts slightly above lambda = 1 and extends to the range of lambda > 2.

The simple solution to this problem is to leave out this mixture "window" altogether, since it is not required for running the engine. Hence, the fast management system controlling the BMW hydrogen engine skips this operating range completely, thus avoiding NOx emissions in the process. As a result, the H2R Record Car is just as powerful as a conventional gasoline-engine car, while at the same time its emissions are limited, for all practical purposes, to nothing but steam.

Safety technology

The fuel system featured in the BMW H2R Record Car is based on a proven series development concept. Fuel is filled into the tank of the H2R prototype at a mobile hydrogen filling station through a manual tank coupling. The vacuum-insulated, double-walled tank has a capacity of more than 11 kilos of liquid hydrogen and is fitted next to the driver's seat. A total of three valves ensures optimum safety, the operating valve on the tank opening at a pressure of 4.5 bar.

Two additional safety valves rule out any dangerous consequences of possible leaks in the jacket around the tank serving to keep the hydrogen at the low temperature required, opening up as soon as pressure within the tank exceeds the limit of 5 bar. This double-redundant safety system guarantees optimum safety at all times, ensuring that the hydrogen tank will not burst as a result of excess pressure.

Heat exchanger instead of a gasoline pump

Gas pressure builds up in the fuel supply system simply because of the rising temperature of the cryogenic, liquid hydrogen in the tank and is kept at an operating pressure of approximately 3 bar by a tank pressure controller. Then the coolant running within the 12 cylinder power unit warms up the hydrogen gas in a heat exchanger to ambient temperature.

Valve technology

Additional valves monitor the pressure of gas in the fuel pipes leading to the engine: Cold low-temperature valves inside the tank control the removal of hydrogen from the tank itself. Should any of the pre-flow pipes develop a leak, with supply pressure dropping below 0.4 bar, the fuel supply valves close automatically, disconnecting and sealing the tank off from its surroundings. The supply pipe can also be interrupted manually by an interruptor tap.

To maintain optimum supply pressure on the injection valves at all times – especially as this pressure may vary as a function of driving conditions - engine management reduces pressure in the supply pipe to approximately 1.2 bar by means of a control valve fitted specifically for this purpose.

This comprehensive safety system featured in the H2R Record Car is supervised additionally by a telemetric system of the same type as in Formula 1. Four hydrogen sensors fitted at neuralgic points - for example in the tank itself and around the tank coupling - recognise any leakage immediately and inform the driver accordingly.

Chassis and suspension

Focusing on the structure and chassis of the BMW H2R Record Car, the engineers and development specialists at BMW Forschung und Technik GmbH used series components carried over from a sophisticated, thoroughbred BMW sports car: the monocoque aluminium spaceframe as well as the entire chassis and suspension system. High-strength aluminium structure panels using the advantages of aluminium as a particularly light material resistant to corrosion fill in the open spaces between the extra-large extrusion-pressed profiles giving the car its stable "skeleton".

The result for the driver is an absolutely excellent, direct driving experience without the slightest vibration or body "tremble".

The front suspension is based on a double-wishbone spring strut front axle together with rack-and-pinion steering, aluminium track control arms, a tiebar, and an anti-roll bar. The front axle subframe is formed by a welded aluminium structure made up of extrusion-pressed profile bars and plates holding all front axle components and bolted to the body at six points. The track control arm made of forged aluminium comes complete with two ball joints in the interest of precise wheel guidance and directional stability.

Wheel guidance and stability at the rear is provided by an integral four-dimensional axle, a multi-arm principle patented by BMW and rounded off in this case by an anti-roll bar. Optimum road contact and safety, finally, is ensured by tyres measuring 245/40 x 19.

The bodyshell: outer skin made of carbon fibre

BMW's designers have also given the H2R Record Car a truly unique body: Measuring 5.40 metres in length and 2 metres in width, the body of the car is designed through and through for optimum streamlining. And to reach record speeds, the frontal area measures just 1.85 square metres and the drag coefficient is a mere 0.21. At the rear a 20-centimetre-long diffuser prevents air swirl behind the car, which might potentially slow it down.

The side profile and sheer length of the H2R prototype also serve to ensure stable driving characteristics at very high speeds. Like on a Formula 1 racing car, the outer skin is made of carbon-fibre-reinforced plastic offering the optimum combination of superior stiffness and low weight: Overall weight of the H2R with a full tank and the driver at the wheel is 1560 kg or 3440 lb.